Syracuse University researchers testing intelligent-systems-based active flow control methods to improve wind turbine efficiency, while University of Minnesota scientists research ways to reduce blade drag

Rachel Carter

Rachel Carter

SYRACUSE, New York , December 21, 2010 (press release) – Engineers at SU's L.C. Smith College of Engineering and Computer Science collaborate with University of Minnesota on new intelligent systems and grooved designs

One issue confronting the efficiency of wind as a promising renewable energy source is the wind itself—specifically, its changeability. While the aerodynamic performance of a wind turbine is best under steady wind flow, the efficiency of the blades degrades when exposed to conditions such as wind gusts, turbulent flow, upstream turbine wakes and wind shear.

Now, a new type of air-flow technology may soon increase the efficiency of large wind turbines under many different wind conditions.

Researchers from Syracuse University's L.C. Smith College of Engineering and Computer Science (LCS) are testing new intelligent-systems-based active flow control methods with support from the U.S. Department of Energy through the University of Minnesota Wind Energy Consortium. The approach estimates the flow conditions over the blade surfaces from surface measurements, and then uses this information in an intelligent controller to implement real-time actuation on the blades to control the airflow and increase the overall efficiency of the wind turbine system. The work may also reduce excessive noise and vibration due to flow separation.

Initial simulation results completed by LCS researchers Guannan Wang, Basman El Hadidi, Jakub Walczak, Mark Glauser and Hiroshi Higuchi show that flow control applied on the outboard side of the blade beyond the half radius could significantly enlarge the overall operational range of the wind turbine with the same rated power output, or considerably increase the rated output power for the same level of operational range. The results suggest that either the overall operational range of the wind turbine could be effectively enlarged by 80 percent with the same rated power output, or the rated output power could be increased by 20 percent while maintaining the same level of operational range when the control is on. The optimal location for the actuator is found to be on the outboard of the blade beyond half of the radius.

The team is also investigating a characteristic airfoil in a new anechoic wind tunnel facility at SU to determine the airfoil lift and drag characteristics with appropriate flow control while exposed to large-scale flow unsteadiness. In addition, the effects of flow control on the noise spectrum of the wind turbine will be also assessed and measured in the anechoic chamber.

"It is exciting for us to be involved in the world-class wind energy consortium led by the University of Minnesota," says Glauser, professor of mechanical and aerospace engineering. "This is a wonderful opportunity to transition our expertise in intelligent systems for flow control, developed largely through support from the aerospace sector, to this important and growing area of the renewable energy sector.''

Scientists at the University of Minnesota are looking at another inefficiency with wind energy—the drag, which is the resistance felt by the turbine blades as they beat the air. The team at the University of Minnesota's Saint Anthony Falls Lab (SAFL) looked at the effect of placing tiny grooves on turbine blades on drag reduction. The grooves are in the form of triangular riblets scored into a coating on the blade surface. They are so shallow (between 40 and 225 microns) that they can't be seen by the human eye—leaving the blades looking perfectly smooth. Through wind-tunnel tests of 2.5-megawatt turbine airfoil surfaces (becoming one of the popular industry standards) and computer simulations, they have looked at the grooves' efficacy for various groove geometries and angles of attack (how the blades are positioned relative to the air stream).

University of Minnesota researchers Roger Arndt, Leonardo P. Chamorro and Fotis Sotiropoulos, believe that riblets will increase wind turbine efficiency by about 3 percent.

Both of these new ideas for enhancing the efficiency of wind turbines were recently presented at the American Physical Society Division of Fluid Dynamics meeting in Long Beach, Calif. On Nov. 21, the SU research team presented "Benefits of Active Flow Control for Wind Turbine Blades," and researchers at the University of Minnesota presented "On the skin friction drag reduction in large wind turbines using sharp V-grooved riblets."

* All content is copyrighted by Industry Intelligence, or the original respective author or source. You may not recirculate, redistrubte or publish the analysis and presentation included in the service without Industry Intelligence's prior written consent. Please review our terms of use.

Share:

About Us

We deliver market news & information relevant to your business.

We monitor all your market drivers.

We aggregate, curate, filter and map your specific needs.

We deliver the right information to the right person at the right time.

Our Contacts

1990 S Bundy Dr. Suite #380,
Los Angeles, CA 90025

+1 (310) 553 0008

About Cookies On This Site

We collect data, including through use of cookies and similar technology ("cookies") that enchance the online experience. By clicking "I agree", you agree to our cookies, agree to bound by our Terms of Use, and acknowledge our Privacy Policy. For more information on our data practices and how to exercise your privacy rights, please see our Privacy Policy.